Subpart J - Welding

60 %
40 %
Information about Subpart J - Welding

Published on July 4, 2009

Author: FFSafety

Source: slideshare.net

1

OCCUPATIONAL SAFETY AND HEALTH OSHA ADMINISTRATION Subpart J – Welding and Cutting 1926.350 Gas welding and cutting 1926.350(a) Transporting, moving, and storing compressed gas cylinders. (1) “Valve protection caps shall be in place and secured.” 1926.350(a)(4) “When cylinders are transported by powered vehicles, they shall be secured in a vertical position.” 2

4

OCCUPATIONAL SAFETY AND HEALTH OSHA ADMINISTRATION Subpart J – Welding and Cutting 1926.350 Gas welding and cutting 1926.350(a)(6) “Unless cylinders are firmly secured on a special carrier intended for this purpose, regulators shall be removed and valve protection caps put in place before cylinders are moved.” 1926.350(a)(9) “Compressed gas cylinders shall be secured in an upright position at all times except, if necessary, for short periods of time while cylinders are actually being hoisted or carried.” 5

6

7

8

9

10

OCCUPATIONAL SAFETY AND HEALTH OSHA ADMINISTRATION Subpart J – Welding and Cutting 1926.350 Gas welding and cutting 1926.350(a)(10) “Oxygen cylinders in storage shall be separated from fuel-gas cylinders or combustible materials (especially oil or grease), a minimum distance of 20 feet or by a noncombustible barrier at least 5 feet high having a fire-resistant rating of at least one-half hour.” 11

12

13

14

15

OCCUPATIONAL SAFETY AND HEALTH OSHA ADMINISTRATION Subpart J – Welding and Cutting 1926.350 Gas welding and cutting 1926.350(f)(2) “When parallel sections of oxygen and fuel gas hose are taped together, not more than 4 inches out of 12 inches shall be covered by tape.” 1926.350(f)(3) “All hose in use, carrying acetylene, oxygen, natural or manufactured fuel gas, or any gas or substance which may ignite or enter into combustion, or be in any way harmful to employees, shall be inspected at the beginning of each work shift. Defective hose shall be removed from service.”

17

OCCUPATIONAL SAFETY AND HEALTH OSHA ADMINISTRATION Subpart J – Welding and Cutting 1926.350 Gas welding and cutting 1926.351(b)(2) “Only cable free from repair or splices for a minimum distance of 10 feet from the cable end to which the electrode holder is connected shall be used, except that cables with standard insulating connectors or with splices whose insulating quality is equal to that of the cable are permitted.” 1926.351(e) “Whenever practicable, all arc welding and cutting operations shall be shielded by noncombustible or flameproof screens which will protect employees and other persons working in the vicinity from the direct rays of the arc.”

19

OCCUPATIONAL SAFETY AND HEALTH OSHA ADMINISTRATION Subpart J – Welding and Cutting 1926.352 Fire prevention 1926.352(d) “Suitable fire extinguishing equipment shall be immediately available in the work area and shall be maintained in a state of readiness for instant use.” 1926.352(i) Drums containers, or hollow structures which have contained toxic or flammable substances shall before welding, cutting, or heating is undertaken on them either be filled with water or thoroughly cleaned of such substances and ventilated and tested….

22

23

24

28

29

30

32

33

34

35

36

37

Add a comment

Related pages

Authority for 1926 Subpart J - 1926 Subpart J

• Part Number: 1926 • Part Title: Safety and Health Regulations for Construction • Subpart: J • Subpart Title: Welding and Cutting • Standard Number:
Read more

Gas welding and cutting. - 1926.350 - Occupational Safety ...

• Part Number: 1926 • Part Title: Safety and Health Regulations for Construction • Subpart: J • Subpart Title: Welding and Cutting • Standard Number:
Read more

Subpart J—Welding and Cutting

246 §1926.350 29 CFR Ch. XVII (7–1–11 Edition) (ii) Inspection shall be made of belts, lacings, and fasteners and such equip-ment kept in good repair.
Read more

29 CFR Part 1926, Subpart J - Welding and Cutting | US Law ...

Status message There is 1 Update appearing in the Federal Register for 29 CFR Part 1926. View below or at eCFR (GPOAccess)
Read more

Subpart J - Welding and Cutting §1926 - Home - APi ...

Subpart J - Welding and Cutting §1926.350 Gas welding and cutting (a) Transporting, moving, and storing compressed gas cylinders. (1) Valve protection ...
Read more

Welding and Cutting - U.S. Government Publishing Office

J Subpart J Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED) SAFETY AND ...
Read more

Construction Standards - 1926 - Subpart J - Welding and ...

This site provides access to the standards developed and an enforced by the Occupational Safety and Health Administraion(OSHA) in the construction industry ...
Read more

Subpart J: Welding - TRACE Fire Protection and Safety ...

Ron Hopkins, CFPS, CFEI, IAFI-F Instructor, EKU OSHA Ed Center 2/17/2014 Ron.Hopkins@eku.edu www.TRACEfireandsafety.com 1 Subpart J: Welding 1926.350 ...
Read more

PPT – Subpart J – Welding/Cutting PowerPoint ...

Subpart J Welding/Cutting 1926.350-354 Welding and Cutting Top 5 Osha citations 350(a)(9) Cylinders secured upright 350(a)(10) Oxygen cylinder storage 352 ...
Read more