advertisement

How to setup call blocking based off of incoming caller's ani

50 %
50 %
advertisement
Information about How to setup call blocking based off of incoming caller's ani
Technology

Published on February 18, 2014

Author: routersbuy

Source: slideshare.net

Description

Leading Cisco networking products distributor-3network.com

How to setup call blocking based off of incoming caller's ani
advertisement

How to setup call blocking based off of incoming Caller's ANI Block incoming Calls based off of ANI. (incoming or originating phone number): the following is an example of how to setup call blocking based off of incoming Caller's ANI. In this example, my voice enviornment consist of an 8.6 CUCM Pub with 3 Subscribers. I have three Cisco 2911 h.323 voice gateways with 1 PRI each. I put together this simple 3 step process based off of a Cisco Configuration guide. I tested it on my cell phone and a coupe of others and it worked great. Here are the three steps: Block Incoming Calls based off of ANI. The following configuration must be applied to each voice gateway. It is done in basically 3 steps: 1. Create a Translation Rule. Within the translation rule you will use the reject command followed by the pattern you wish to reject. In this case we use the entire phone number. router#conf t router(config)#voice translation-rule 1 router(config-xxx)#rule 1 reject /8055553538/ router(config-xxx)#rule 2 reject /4805557904/ Moving forward, you can continue to add rules to reject numbers as you see fit. example: router(config-xxx)#rule 3 reject /4805557905/ and so on. 2. Apply the Translation rule to a Translation Profile and give it a name. (This will be used to apply to the incoming Dial-peers.) router#conf t router(config)#voice translation-profile call_block router(config-xxx)#call-block disconnect-cause incoming call-reject in this case we named the Translation Profile "call_block" 3. Apply Translation Profile to incoming Dial-peers (only) on each router. router#conf t router(config)#dial-peer voice 1 pots router(config-xxx)#call-block translation-profile incoming call_block router(config-xxx)#call-block disconnect-cause incoming call-reject 1

In our case, we apply this to dial-peers 1 and 2 on each voice gateway as these are the incoming dial-peers for each location. Each dial-peer looks like this after configuration: (at least in our enviornment) dial-peer voice 1 pots call-block translation-profile incoming call_block call-block disconnect-cause incoming call-reject incoming called-number .T direct-inward-dial port 0/0/0:23 Hope this helps for anyone out there looking to block based off incoming numbers. It is referred from: https://supportforums.cisco.com/docs/DOC-25415 More related: Cisco router rules of nomenclature Enterprise router recommendation: Cisco 2911 router How To Recover Cisco Router Password The Difference of The Cisco Catalyst 2900 and Cisco Catalyst 1900 More Cisco products and Reviews you can visit: http://www.3anetwork.com/blog : 3Anetwork.com is a world leading Cisco networking products wholesaler, we wholesale original new Cisco networking equipments, including Cisco Catalyst switches, Cisco routers, Cisco firewalls, Cisco wireless products, Cisco modules and interface cards products at competitive price and ship to worldwide. Our website: http://www.3anetwork.com Telephone: +852-3069-7733 Email: info@3Anetwork.com Address: 23/F Lucky Plaza, 315-321 Lockhart Road, Wanchai, Hongkong 2

Add a comment

Related presentations

Presentación que realice en el Evento Nacional de Gobierno Abierto, realizado los ...

In this presentation we will describe our experience developing with a highly dyna...

Presentation to the LITA Forum 7th November 2014 Albuquerque, NM

Un recorrido por los cambios que nos generará el wearabletech en el futuro

Um paralelo entre as novidades & mercado em Wearable Computing e Tecnologias Assis...

Microsoft finally joins the smartwatch and fitness tracker game by introducing the...

Related pages

Block incoming Calls based off of ANI. (incoming or ...

The following is an example of how to setup call blocking based off of incoming ... process based off of a ... Incoming Calls based off of ANI ...
Read more

Blocking Calls Based on Calling Party ID | IP Telephony ...

Adding Call Blocking Based on Calling Party ... the block incoming calls based on ANI, ... the blocking based on caller ID over SIP ...
Read more

International Avaya Users Group : Forums : Blocking ...

... she mentions blocking incoming calls from ... be able to filter based on caller ID/ANI. ... an incoming caller. i have the vdn avector setup but ...
Read more

International Avaya Users Group : Forums : Blocking an ...

Blocking an incoming call by ... inbound call that does not include ANI/Caller ID goes ... explore more in avaya..one way is by incomming call ...
Read more

T-Lock Call Blocker – Version 5.0 - Hqtelecom

Turn feature ON/OFF to Block calls with no caller ID ... Block incoming calls any time ... video on how to install / setup the T-Lock Call Blocker
Read more

How to Block Incoming Calls - HowStuffWorks

How to Block Incoming Calls. ... Other options include anonymous call blocking, which blocks any incoming ... which identifies preferred callers ...
Read more

Co n figuring Call Blocking - Cisco Systems, Inc

Call Blocking Based on Date and Time ... SIP and POTS calls that go through the Cisco Unified CME router. All incoming calls to the ... Last Setup Time = 0.
Read more

How to setup caller ID routing on the Mitel 5000 - YouTube

This video shows you how to setup call routing on the Mitel 5000 Phone ... on the Mitel 5000 Phone System based on the callers ... Off History ...
Read more

Anonymous Call Blocking | Ooma Telo | Support

Anonymous Call Blocking. ... between anonymous incoming ... dial *82 prior to entering your phone number to turn off their anonymous caller ...
Read more