advertisement

How to instal the cisco modules in cisco 4500 switch

67 %
33 %
advertisement
Information about How to instal the cisco modules in cisco 4500 switch
Technology

Published on February 19, 2014

Author: routersbuy

Source: slideshare.net

Description

Leading Cisco networking products distributor-3network.com
How to instal the cisco modules in cisco 4500 switch
advertisement

How to Instal the Cisco Modules in Cisco 4500 To install Cisco modules in a Catalyst 4500 series switch, follow these steps: Step 1 Take the necessary precautions to prevent ESD damage. Wear a grounded ESD wrist strap while handling the modules, and keep them in ESD-protective bags when they are not installed in a chassis. Step 2 Choose a slot for the new module. Verify that you have enough clearance for any interface equipment that you are connecting directly to the switching module ports. Step 3 Loosen the captive installation screws that secure the existing module or the blank module filler plate in the slot you want to use. Step 4 Remove the existing module and immediately place it on an antistatic mat or in an antistatic bag. If you are removing a blank module filler plate, set the blank module filler plate aside for future use. Note To ensure the proper air flow and to maintain EMI protection, make sure that there is a blank module filler plate (C4K-SLOT-CVR-E) installed in any unused chassis slot. If a chassis slot are left open, air circulation is disrupted and the fans may not be able to adequately cool the other modules in the chassis. Step 5 Remove the new module from its packaging being careful to handle the module using only the module’s metal tray or the front panel. Do not touch the printed circuit board or the connector pins. Step 6 Position the module in front of the chassis slot and align the edges of the module carrier with the slot guides on the sides of the switch chassis. (See Figure 1.) 1

Step 7 Pivot the two module ejector levers out away from the module faceplate. Step 8 Carefully slide the module into the slot until the notches on both ejector levers engage the chassis sides (the ejector levers start to pivot in towards the faceplate). Step 9 Using your thumb and forefinger of each hand, simultaneously pivot in both ejector levers, as shown in Figure 2, to fully seat the module in the backplane connector. Caution: Always use the ejector levers when installing or removing modules. A module that is only partially seated in the backplane causes the system to halt and subsequently crash. 2

Note: If you perform a hot swap, the console displays the message “Module n has been inserted.” This message also appears if you are connected to the Catalyst 4500 series switch through a Telnet session. Step 10 Use a screwdriver to tighten the captive installation screw on each end of the module faceplate (see Figure 2). Step 11 Install any necessary transceivers in the module ports. Installation instructions along with safety warnings for the various types of transceivers can be found at the following URL: http://www.cisco.com/en/US/products/hw/modules/ps5455/prod_installation_guides_list.h tml Step 12 Attach any necessary network interface cables or other devices to the interface ports. Step 13 Check the status of the module as follows: a. Ensure that the LED labeled STATUS is green (module operational). b. When the switch is on line, enter the show module command. Verify that the system acknowledges the new module and that the module status is good. Step 14 If the module is not operational, try reseating it in the slot. If the module is still not operational, contact your customer representative. referred from: It is http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/hardware/configuration/notes/OL _25315.pdf More related: Cisco router rules of nomenclature Enterprise router recommendation: Cisco 2911 router How To Recover Cisco Router Password Problems configuration for Cisco Catalyst 4500 Cisco Module WS-X4648-RJ45V+E compatibility with Cisco 4506 (12.2(25)EWA4) More Cisco products and Reviews you can visit: http://www.3anetwork.com/blog 3Anetwork.com is a world leading Cisco networking products wholesaler, we wholesale 3

original new Cisco networking equipments, including Cisco Catalyst switches, Cisco routers, Cisco firewalls, Cisco wireless products, Cisco modules and interface cards products at competitive price and ship to worldwide. Our website: http://www.3anetwork.com Telephone: +852-3069-7733 Email: info@3Anetwork.com Address: 23/F Lucky Plaza, 315-321 Lockhart Road, Wanchai, Hongkong 4

Add a comment

Related presentations

Presentación que realice en el Evento Nacional de Gobierno Abierto, realizado los ...

In this presentation we will describe our experience developing with a highly dyna...

Presentation to the LITA Forum 7th November 2014 Albuquerque, NM

Un recorrido por los cambios que nos generará el wearabletech en el futuro

Um paralelo entre as novidades & mercado em Wearable Computing e Tecnologias Assis...

Microsoft finally joins the smartwatch and fitness tracker game by introducing the...

Related pages

How to instal the cisco modules in cisco 4500 switch ...

1. How to Instal the Cisco Modules in Cisco 4500 To install Cisco modules in a Catalyst 4500 series switch, follow these steps: Step 1 Take ...
Read more

Catalyst 4500 E-Series Module Installation Note - Cisco

Cisco Catalyst 4500 Series ... To install modules in a Catalyst 4500 series ... To remove a switching module from a Catalyst 4500 series switch, ...
Read more

Catalyst 4500 Series Supervisor Engines and Switching ...

Installing Supervisor Engines and Switching Modules . All Catalyst 4500 series switches support hot swapping, which lets you install, remove, replace, and ...
Read more

Installing the Cisco uMG9850 QAM Module - MIK

This quick start guide describes how to install a Cisco uMG9850 QAM Module in a ... QAM Module The Cisco uMG9850 ... Cisco Catalyst 4500 series switch ...
Read more

Virtual switching system (VSS) Configuration For Cisco ...

Virtual switching system (VSS) Configuration For Cisco 4500 series switches ... (switch/module/port).
Read more

Configuration module supervisor Switch Catalyst 4500 | LAN ...

Configuration module supervisor Switch Catalyst 4500 ... Cisco Technical Support Forum | 6016 ... Cisco bpdu guard:
Read more

Catalyst 4507R-E Switch Module problem - 87535 - The Cisco ...

I have inserted one Switch Module (WS-X4548-GB-RJ45V) ... Catalyst 4500 Series Switch Cisco IOS Software Configuration Guide, 12.2(31)SG ...
Read more

Cisco Catalyst 4948E Ethernet Switch - Cisco

Catalyst 4500 Series Switch Cisco IOS Command ... Cisco Catalyst 4900M Switch Data Sheet; Install and ... Transceiver Modules Maintenance and ...
Read more

Cisco - High Availability and Redundancy in Catalyst 4500 ...

High Availability and Redundancy in Catalyst 4500 Series Switches ... • Catalyst 4507R with dual Supervisor IV modules • Cisco IOS ... Switch#show module
Read more