Forming operations

50 %
50 %
Information about Forming operations

Published on March 5, 2014

Author: vicky937

Source: slideshare.net

FORMING OPERATIONS by Waqas ahmed

Forming operation  Forming process make use of suitable stresses like compression, tension, shear or combined stresses to cause plastic deformation of the materials to produce required shapes. In forming, no material is removed i.e. they are deformed

Some of the forming processes are: Forging Extrusion Rolling Drawing

Forging process  Forging is a manufacturing process involving the shaping of metal using localized compressive forces.

Forging process

Introduction     A metal is shaped by compressive forces Oldest metal working process – 4000BC Can be performed with a hammer and anvil Typical forged products:     Bolts Rivets Connecting rods Gears

Lading-gear components for the C5A and C5B transport aircraft, made by forging. Steps involved in forging a bevel gear with a shaft.

Grain Structure    Parts have good strength High toughness Forgings require additional heat treating Fig : A part made by three different procedures, showing grain flow (a) casting (b) machining (c) forging

Open-Die Forging   Is the simplest forging process Sizes can very from very small parts to very large parts

Impression-Die & Closed-Die Forging  The workpiece acquires the shape of the die cavities while being forged between the two shaped dies

Precision Forging      Used for economic reasons The part formed is close to the final dimensions Less machining is needed Higher capacity equipment is needed Aluminum and Magnesium alloys work well in the process

Coining     Closed-die forging process Used for minting coins, medallions, & jewelry Lubricants can not be used in coining Can be used to improve surface finish

Extrusion process  Extrusion is a manufacturing process used to create objects of a fixed cross-sectional profile. A material is pushed or drawn through a die.

Extrusion process

Rolling process  In metalworking , rolling is a metal forming process in which metal stock is passed through a pair of rolls.

Rolling process

Drawing process  Drawing is a metal working process which uses tensile forces to stretch metal. ...Cold drawing is primarily used in manufacturing plastic .

Drawing process

Sheet metal The success of forming is in relation to two things, the flow and stretch of material. As a die forms a shape from a flat sheet of metal, there is a need for the material to move into the shape of the die. The flow of material is controlled through pressure applied to the blank and lubrication applied to the die or the blank. If the form moves too easily, wrinkles will occur in the part. To correct this, more pressure or less lubrication is applied to the blank to limit the flow of material and cause the material to stretch or thin. If too much pressure is applied, the part will become too thin and break. Drawing metal is the science of finding the correct balance between wrinkles and breaking to achieve a successful part.

Deep drawing Main article: Deep drawing Sheet metal drawing becomes deep drawing when the workpiece is drawing longer than its diameter. It is common that the workpiece is also processed using other forming processes, such as piercing, ironing, necking, rolling, and beading.

Bar, tube & wire Bar, tube, and wire drawing all work upon the same principle: the starting stock drawn through a die to reduce the diameter and increase the length. Usually the die is mounted on a draw bench. The end of the workpiece is reduced or pointed to get the end through the die. The end is then placed in grips and the rest of the workpiece is pulled through the die.[1] Steels, copper alloys, and aluminium alloys are common materials that are drawn.[3] Drawing can also be used to produce a cold formed shaped cross-section. Cold drawn cross-sections are more precise and have a better surface finish than hot extruded parts. Inexpensive materials can be used instead of expensive alloys for strength requirements, due to work hardening.[4]

Plastic drawing Plastic drawing, sometimes referred to as cold drawing, is the same process as used on metal bars, but applied to plastics.[6] Cold drawing is primarily used in manufacturing plastic fibers. The process was discovered by Julian Hill in 1930 while trying to make fibers from an early polyester.[7] It is performed after the material has been "spun" into filaments; by extruding the polymer melt through pores of a spinneret. During this process, the individual polymer chains tend to somewhat align because of viscous flow. These filaments still have an amorphous structure, so they are drawn to align the fibers further, thus increasing crystallinity, tensile strength and stiffness. This is done on a draw twister machine.[7][8] For nylon, the fiber is stretched four times its spun length. The crystals formed during drawing are held together by hydrogen bonds between the amide hydrogens of one chain and the carbonyl oxygens of another chain.

Add a comment

Related presentations

Related pages

forming operation - Englisch ⇔ Deutsch Wörterbuch - leo.org

Das Sprachangebot für Englisch-Deutsch: Wörterbuch mit Übersetzungen, Flexionstabellen und Audio, interaktivem Forum und Trainer für flexibles Lernen.
Read more

Forming (metalworking) - Wikipedia, the free encyclopedia

Forming, or metal forming, is the metalworking process of fashioning metal parts and objects through mechanical deformation; the workpiece is reshaped ...
Read more

INTRODUCTION TO SHEET METAL FORMING PROCESSES

metal forming operation can always be, from the conceptual point of view, divided in two stages: ... Introduction to sheet metal forming processes
Read more

Top 25 Forming Operations profiles | LinkedIn

Here are the top 25 Forming Operations profiles on LinkedIn. Get all the articles, experts, jobs, and insights you need.
Read more

BENDING AND FORMING OPERATIONS - Home - Access Engineering ...

8. BENDING AND FORMING OPERATIONS 8.1. STRESS, STRAIN, ELONGATION, COMPRESSION The process of material forming (i.e., deformation) depends on several laws,
Read more

Tureng - forming operations - Turkish English Dictionary

English Turkish online dictionary Tureng, translate words and terms with different pronunciation options. cold forming operations soğuk biçimleme ...
Read more

Process parameters influence on friction coefficient in ...

In conventional sheet forming processes, such as stamping or drawing, ... Process parameters influence on friction coefficient in sheet forming operations.
Read more

Process planning for metal forming operations : an ...

Process planning for metal forming operations : an integrated engineering-operations perspective: Amazon.de: Anantaram Balakrishnan, Stuart Bryan Brown ...
Read more

Forming processes - Wikipedia, the free encyclopedia

Forming processes are particular manufacturing processes which make use of suitable stresses (like compression, ... Explosive forming; Electromagnetic forming
Read more

Process planning for metal forming operations : an ...

ProcessPlanningforMetalFormingOperations: AnIntegratedEngineering-Operations Perspective AnantaramBalakrishnan and StuartBrown WP#3432-92-MSA May,1992
Read more