Published on February 17, 2014
Evaporation Boats: Top 10 Questions Answered Q.1 What should I do if one evaporation boat fails during the cycle? Breaking the cycle and replacing one boat causes a lot of wastage. Diagram (a) Ans. As the roll of thin film moves from one end to the other inside the vacuum chamber, it moves over sets of evaporation boats that are clamped at intervals. Engineers handling the vacuum deposition keep an eye on the entire process through sight glass provided on the chamber walls. In case he sees that one of the boats has failed during operation, the best course of action for him will be to increase the power and wire feed of two boats adjacent to the failed one. As shown in the diagram(a), for example, if in a set of boats, boat B fails then power and wire feed to boat A and C should be increased. This will cause a bigger fountain of vaporized metal to emerge from these boats, which will compensate for the loss of evaporation from the failed boat- B.
This can save wastage of film, loss of time and power for breaking vacuum and replacing boat and then starting all over again. Q.2 There are 2 and 3 Component Evaporation Boats. What's the difference between them? Ans. A two component Evaporation boat is made of Titanium Diboride (TiB2) and Boron Nitride (BN). A three component boat is made of Titanium Diboride (TiB2), Boron Nitride (BN) and Aluminum Nitride (AlN). A three component boat is marginally cheaper than a two component boat but its life is also shorter than a two component boat by almost 25%. Therefore, people generally prefer a two component boat for better performance and their money’s worth. Q.3 How can I get more life from evaporation boats used in metalizing? Ans. Life of evaporation boats can be increased by about 25 percent if operating parameters are optimized. I have written an article earlier on this topic. Click here to read it. Q.4 Evaporation boats are of various shapes. Which one is most economical to use? Ans. Evaporation Boats are of following types:1. Rectangular with cavity 2. Rectangular without cavity 3. Rectangular with no cavity but thin grooves cut on top surface by laser 4. Trapezium shaped 5. Triangular shaped
Experience has shown that rectangular boats with cavity work out to be most economical & efficient. This is because of the following reasons: a) Robust shape b) Long life c) Ease of clamping d) Optimum use of current e) Better evaporation characteristics. More than 99% Metallizers, world over use rectangular evaporation boats with cavity. Q.5 What is the difference between dimet evaporation boats and trimet evaporation boats? Ans. Dimet boats are made of titanium diboride as conducting element and boron nitride as insulating element. In trimet boats part of boron nitride is substituted by aluminum nitride to reduce cost. Although 3 component boats are cheaper than 2 component boats, they give a shorter working life.
Q.6 How are evaporation boats made? Ans. For manufacture of evaporation boats ceramic powders titanium diboride and boron nitride are mixed thoroughly. After mixing these are pressed under high temperature. With this one gets a composite ceramic billet. This billet is than cut into evaporation boats. For details please read my blog post at - Evaporation Boat: How It Is Made Q.7 What are BN boats that are used in a metallizer? Ans. BN boats are nothing but normal evaporation boats. Some people (mostly Chinese) call evaporation boats as BN boats because evaporation boats have boron nitride powder as one of its constituents. Q.8 Why should graphite foil be used at the boat ends? Can I use ordinary graphite foil? Ans. Boats are given current through copper clamps. This current flows at very high amperage. Neither the surface of clamp nor the surface of boat is perfect. So contact between the two leaves small gaps. These small gaps cause sparking which results in (a) wastage of electricity (b) overheating of copper clamp causing it to break or warp and (c) damage to boat. To prevent this, graphite foil is used; graphite being conductive in nature. Graphite foil is a thin paper like material made up of highly compressed graphite. It is wrapped around the ends of boat and then fitted into the clamp. Graphite foil of myriad qualities are available in the market. Sometimes just to save money, low quality plumber grade graphite foil is used. But it is not advisable to do so. These low quality graphite foils have low compressibility and many additives like binders and adhesives in them. Conductivity of this low quality graphite foil is poor causing overheating. Also on getting heated, these binders release vapors into the vacuum chamber which can adhere to the substrate as impurities. Good quality graphite foil will ensure proper electrical contact between boat and the clamp and will be free of binders and adhesives.
Supervac is manufacturer and supplier of high quality graphite foil SV-GF. It is manufactured specially for the vacuum coating industry by a patented process of exfoliation. Q.9 Why is it important to heat the boats slowly for first use? Ans. New boats invariably have some moisture. If boats are heated slowly this moisture turns into steam and escapes through the pores of the boat. If boat is heated fast then moisture (turned into steam) will have no time to escape and pressure buildup can cause the boat to crack. Q.10 My ceramic boats puncture very quickly. Any remedies for this?
Ans. There are two likely reasons for this: 1) You may be using very hard aluminum wire. 2) The rate of feed for aluminum wire is too fast. Remedy: Use tempered aluminum wire and/or reduce the wire feed speed to solve this problem.
Presentación que realice en el Evento Nacional de Gobierno Abierto, realizado los ...
In this presentation we will describe our experience developing with a highly dyna...
Presentation to the LITA Forum 7th November 2014 Albuquerque, NM
Un recorrido por los cambios que nos generará el wearabletech en el futuro
Um paralelo entre as novidades & mercado em Wearable Computing e Tecnologias Assis...
Evaporation Boats: Top 10 Questions Answered Q.1 What should I do if one evaporation boat fails during the cycle? Breaking the cycle and replacing one boat ...
Ceramic Evaporation Boats are an expensive consumable required by the vacuum coating industry. In this article, Anshuman Punj, CEO of Supervac Industries ...
Evaporation boats: Top 10 questions answered. ... Q.1 What should I do if one evaporation boat fails during the cycle? Breaking the cycle and replacing one ...
Graphite Foil Top 10 Questions Answered. ... it provides better contact between evaporation boats and copper clamps. Q.10 Some suppliers supply ...
Share Booster Pump Oil Top 7 Questions Answered. ... Evaporation boats top 10 questions answered. ... 2014 TOP 10 QUESTIONS ANSWERED INCORRECTLY ON IAABO EXAM.
Width of graphite tape is determine by the size of evaporation boats. Q.3 Why use expensive Graphite Foil for a Metallizer? eX r Tr t P ia D l F
Booster Pump Oil Top 7 Questions Answered; of 4
More questions about Science & Mathematics, why. Weknowtheanswer. ABOUT; FIND THE ANSWERS. ... Evaporation boats get current from copper clamps and get ...
Anshuman Punj. Anshuman Punj is a post-graduate mechanical engineer and an MBA by qualification. (B.Tech.-Mechanical Engineering, M.Tech.-Tool Design, MBA ...