Published on March 3, 2014
DrayTek Training – Configuration Reference Guide 1. WAN Configuration Connect a Laptop to LAN port, by default it will have DHCP enabled and give an IP in the 192.168.1.x range. Then Browse to 192.168.1.1 login with admin / admin Go to WAN – Internet Access and set Access Mode to “Static or Dynamic IP” Tick “Enable” and enter the given IP. Save and reboot. After reboot verify that the WAN is on, WAN1 is green and LED starts blinking.
You should be able to access the Internet now 2. LAN To be able to configure multiple LANs we first need to enable Vlans. Go to LAN – VLAN – and tick on Enable. Associate all Ports to LAN1. Router reboots After reboot go to LAN – General Setup and enable LAN2 and interVlan routing for Lan1/Lan2. Click OK and reboot again.
Go to LAN – General Setup and click on “Details Page”. Configure the LAN IP and DHCP server settings according to the instructions. Click OK and reboot Your Laptop gets a new IP in the LAN range configured Access the new LAN IP just configured. And configure LAN 2 IP as instructed. Connect the IP phone to port 5 and reboot the phone. Verify it gets an Ip in same range. To check Go to Diagnostics – DHCP Table and open the Ip Phone GUI. We will configure Vlans for the phone in next step.
3. VLAN Go to LAN – VLAN and configure according to the instructions. Click OK and reboot Make sure the phone is connected to port 5. Set the Vlan on the phone using phone’s buttons: Settings -‐> navigate to the right -‐> VLAN Settings -‐> ID=10 -‐> Check button -‐> navigate to the right and Reboot the phone Connect a Laptop to LAN port on the phone. Verify that the phone gets an IP in LAN2 and laptop an IP in LAN1. Ping or browse the new Phone’s IP. You should now have two VLANs working.
4. VPN Go to VPN and Remote Access – LAN to LAN and click on 1. Configure according to instructions and as shown below. Make sure you configure remote IPs, and Shared Key for both dial in and dial out
Test connection by going to “Connection Management” and ping a remote LAN IP. 5. Load Balancing and Route Policy TO Set Auto-‐Weight oad balancing under WAN – General Setup
Configure Route-‐Policy so all traffic to a specific Ip goes on WAN1 or VPN Run a tracert from your Laptop or got to Diagnostics – Nat Sessions Table to verify that traffic to that Ip goes thru right Wan or VPN 6. Firewall To activate the Web Content Filter go to CSM – Web Content Filter Profile You need to have an account on myvigor.draytek.com portal
Before configuring rules verify that you can access myspace.com, yahoo.com and facebook. Create keyword objects: Configure Web Content Filtering to block Social Media with a Whitelist and Apply Apply the filters created to a Firewall rule so they can take effect:
Try connecting to facebook, then try connecting to myspace.com (whitelisted) Configure URL Filter Follow the instructions Configure User Management Follow the instructions
Features Guide. Learn about some of DrayTek's advanced features. ... DrayTek is the leading manufacturer of business class broadband and networking solutions.
On most DrayTek product, ... Take a backup of your current configuration before upgrading and have a copy of the old firmware to hand in ... User Guide ...
DrayTek Telnet Commands Reference Guide. ... v” to view the configuration of ... Password=draytek 90 Telnet Command Reference Guide V1.1 2 ...
i Vigor 2820 Series Quick Start Guide ... DrayTek Corp. declares that Vigor2820 Series of routers are in compliance with the ... 3.1 Basic Configuration ...
FORTINET VIDEO GUIDE http://video.fortinet.com ... FORTINET TRAINING SERVICES ... configuration.InFortiClient ...
Vigor Ap 800 User Manual ... (220-240VAC), quick start guide, manual on CD-Rom. DrayTek, ... training - Configuration Reference Guide.
Training & Events; Partners; Guest. Search ... Cisco ASA Services Module CLI Configuration Guide, 8.5 ; Cisco ASA 5500 Series Configuration Guide using ...
Training Discover training and ... Get Started Guide for ... Includes written guidance and reference implementations. ...