50 %
50 %
Information about Chapter4

Published on November 7, 2007

Author: Sevastian


Lecture Note:  Lecture Note Address 4. The Transfer function:  4. The Transfer function What is Transfer Function? ; an algebraic expression for the dynamic relation between the input and output of the process model. It is defined so as to be independent of the initial conditions and of the particular choice of forcing function. Properties; It can be derived only for a linear differential equation model because Laplace transform can be applied only to linear equations. If model is non-linear, then it must be linearized first. Advantage; It is easy to interpret and use in calculating output responses for particular input changes. 4.1 Development of Transfer Functions:  4.1 Development of Transfer Functions Example ; Stirred-tank heating system Energy balance equation. Figure 4.1. Continuous stirred-tank heater. Slide4:  Assumption ; constant liquid holdup and constant inflow(w is constant), a linear model result. If the process is at steady-state, . Subtract (4-3) from (4.1). Define some important new variables(Deviation variables). By substituting deviation variables for variables, the transfer functions are not related to initial conditions. Slide5:  Let . Apply Laplace Transform. If . If . 4.2 Property of Transfer Functions:  4.2 Property of Transfer Functions 1. The steady-state output change for a sustained change in input can be calculated directly; we can easily obtain steady state gain K. - Final value theorem. Steady State gain; the ratio of the output variable change to an input variable change when the input is adjusted to a new value and held there, thus allowing the process to reach a new steady state. 2. The transfer function has the order of the denominator polynomial (in s) as same as the order of the equivalent differential equation. General n-th order differential equation. Slide7:  Apply Laplace transform to (4.15). For step input function, obtain the gain K. Physical Realizability. ( ) - if for step input change,( ), which has infinite size, should be infinite size at t=0. Therefore, assumption is contradictive (unrealizable), and . Slide8:  3. Additive property of the transfer function in parallel processes. 4. Multiplicative property of the transfer function in series processes. Figure 4.3. Block diagram of Multiplicative(series) transfer function model. Slide9:  Example; Two liquid surge tanks in series. Figure 4.4. Schematic diagram of two liquid surge tanks in series. Assumption;  The outflow from each tank is linearly related to the height of the liquid(head) in that tank.  The two tanks have different cross-sectional areas and , and that the outflow valve resistance are fixed at and . Find the transfer function relating changes in outflow from the second tank, , to changes in inflow to the first tank, . Show how this transfer function is related to the individual transfer functions, and . and denote the deviations in Tank 1 and Tank 2 levels, respectively. Slide10:  For tank 1. Putting (4-21) into deviation variable form gives Apply Laplace transform and rearrange to obtain transfer function. Similarly, other transfer functions are obtained as follows. Slide11:  The desired transfer function relating the outflow from Tank2 to the inflow to Tank 1 can be derived by forming the product of (4-23) through (4-26). Figure 4.5. Input-output model for two liquid surge tanks in series. 4.3 Linearization of Non-linear Models:  4.3 Linearization of Non-linear Models Necessity There is a wide variety of processes for which the dynamic behavior on the process variables in a non-linear fashion. Laplace transform cannot be applied! How? Taylor series expansion. For around the nominal steady-state operating point . Where y is the output and x is input. At steady state, . Put (4-29) into deviation variable form. Slide13:  Example; A liquid-level storage system. Assume that the valve discharge rate is related to the square root of liquid level; . Derive an approximate dynamic model for this process. Material balance. Deviation variables. Linearize about the steady-state conditions . Slide14:  Useful results of Taylor series expansion. (1) , where n is real. Ex) (2) (3) (4)

Add a comment

Related presentations

Related pages

Chapter 4

Chapter 4 is a PR and Communications agency network, focused on Public Relations, Public Affairs, Business and Marketing Communications Consulting in ...
Read more

Chapter4 communication design

Chapter4 communication design - Informationen über Jan Hansmann, Student der Wirtschaftspsychologie aus Norddeutschland
Read more

Chapter4 | PR kao uspešni odnosi s javnošću za podršku ...

Kvalitetna komunikacija direktno i pozitivno utiče na poslovanje kompanije, njenih ljudi, brendova i proizvoda. Pr agencija Chapter 4 se bavi konsaltingom ...
Read more

Chapter 4 HU

Chapter 4 ist ein PR- und Kommunikationsagenturnetzwerk mit Schwerpunkt Öffentlichkeitsarbeit, Unternehmensberatung, Marketingberatung und Public Affairs ...
Read more

CHAPTER 4 - Alcohol and Tobacco Tax and Trade Bureau

CHAPTER 4 CLASS AND TYPE DESIGNATION GENERAL FEATURES nIdentifies the labeled distilled spirits as to its specific class and/or class and type
Read more

\chapter Wiki .:. goLaTeX - Mein LaTeX-Forum

chapter. Seite; Diskussion; bearbeiten; Versionen/Autoren; Dieser Befehl ist ein Gliederungsbefehl und erstellt ein neues Kapitel in LaTeX. Wie in der ...
Read more


*CHAPTER4 Pathophysiology anddifferentialdiagnosis ofanaemia Jean-FrançoisLambert,PhotisBeris IRON2009_CAP.4(108-141):EBMT2008 4-12-2009 16:05 Pagina 108
Read more

WHO | Chapter 4

Chapter 4 Environmental risks. The environment in which we live greatly affects our health. The household, workplace, outdoor and transportation ...
Read more

Chapter 4 Final 0910 - European Commission

Chapter 4: Documentation Legal basis for publishing the detailed guidelines: Article 47 of Directive 2001/83/EC on the Community code relating to medicinal ...
Read more

Chapter 4 - Automate the Boring Stuff with Python

Say you have the list ['cat', 'bat', 'rat', 'elephant'] stored in a variable named spam. The Python code spam[0] would evaluate to 'cat', and spam[1] would ...
Read more