Calorimetry Lab

50 %
50 %
Information about Calorimetry Lab

Published on February 15, 2014

Author: emmawise



Fun lab on food energy! Calculating the number of ACTUAL calories in a cheese puff vs what it says on the package- includes pre-lab questions, procedure, data table, guided calculations, analytic/conclusion questions, percent error calculation, scaffolded summary of experiment to be filled in. Includes highlighted/filled in portions for teacher reference!

FOOD ENERGY Have you ever counted Calories? Food energy is measured in Calories (upper case C) • It takes 1000 calories to make up a Calorie Example: A standard French fry serving contains 220 Calories of food energy. How many calories are present? 220 Calories x 1000 cal/Cal. = 220,000 calories It takes 1 calorie to raise the temperature of 1 g of water 1 °C Simplified formula may be used: calories = grams of water x (final °C – initial °C) This is determined by the burning of food under controlled conditions (CALORIMETRY) using an instrument called a calorimeter. Pre-lab problem: 1. You want to raise the temperature of 250mL of water from 22 °C to 99 °C. How much heat energy will be needed? Use equation calories = grams of water x (final °C – initial °C) (250 g) x (77) = 19,250 calories = 19.25 Calories

EXPERIMENT: CALORIES IN A CHEESE PUFF Hypothesis: We predict that there are _____fewer_____ Calories in a cheese puff than the number listed on the nutrition label. DATA TABLE ½ Cheese Puff Sample #1 Mass (g) Original 1.1 Final 0.6 Change 0.5 Temperature (°C) Original Final 28.6 34 Change 5.6 #2 #3 Procedure 1. Obtain ½ a cheese puff. Record it’s mass (ORIGINAL). 2. Pour exactly 100 mL tap water into the aluminum can. Record the temperature of the water in the can (ORIGINAL). 3. Place the ½ cheese puff on the tab in the bottom can. Indicate with a RED CUP when ready for a teacher to ignite cheese puff. Immediately place the can filled with 100 mL of water over the burning puff. 4. Keep the thermometer inside the can, but make sure it is NOT touching the side or bottom. 5. Allow the puff to burn until it goes out. 6. Record the water’s highest temperature (FINAL). 7. Record the mass of charred puff (FINAL). CALCULATIONS AND QUESTIONS Answer these questions on a SEPARATE sheet of paper. 1. Calculate the calories of heat from the burning puff. The 100 mL water has a mass of 100 g (for all practical purposes the density of water is 1 gram/mL) and the specific heat of water is one calorie/degree Celsius/gram (1 calorie/gram °C = 4.186 joule/gram °C).

Use the following equation to make the calculation. calories = (grams of water) x (temperature change) x (specific heat of water) calories = (100g) x (34 °C – 28.6 °C) x (1 calorie/gram °C) = 540 calories 2. Divide the calories from question 1 by the change in mass of the puff. This determines the calories released per gram of puff burned. Record your answer in Kcal or Calories. 540 calories / (1.1 g – 0.6 g) = 1080 calories/g = 1.08 Calories/g 3. Multiply the measured Calories by the number of grams in a serving size, obtained from nutritional panel. 1.08 Calories/g x (28 g/14 cheese puffs) = 2.16 Calories/cheese puff 4. Compare your Calorie results to the nutritional panel. 150 Calories / 14 cheese puffs = 10.71 Calories/cheese puff > 2.16 Calories/cheese puff 5. Conclusion: There are _____fewer_____ Calories in a cheese puff than the number listed on the nutrition label. 6. Calculate your percent error. (actual – measured Calories per serving) x 100 = actual Calories per serving (5.36 – 1.08) x 100 = 79.85% (5.36) 7. Why do you suppose the calculated values for calories per gram are less than the actual value listed on the nutrition label? What could account for the difference? What are possible reasons for the inaccuracy? • • • Didn’t burn the entire cheese puff- had mass left over Burning cheese puff could have lost heat to air/surroundings instead of transferring all heat energy directly to the water filled can Inaccurate temperature readings Scaffolded summary of experiment: The increase in the __temperature__ of the water shows that ___heat energy___ had been stored in the cheese puff, which was released while it burned. We can look at the change in ___heat/temperature___ of the water to find out how much ___heat energy___ is trapped/stored in a cheese puff (the change in enthalpy).

Add a comment

Related presentations

Related pages

Calorimetry Lab - Specific Heat Capacity

Calorimetry Lab - Specific Heat Capacity Introduction Experience tells us that if a hot piece of metal is added to water, the temperature of the water will ...
Read more

Calorimetry Lab Gizmo : Lesson Info : ExploreLearning

Calorimetry Lab. Investigate how calorimetry can be used to find relative specific heat values when different substances are mixed with water. Modify ...
Read more

Calorimeters and Calorimetry - The Physics Classroom

Calorimeters and Calorimetry; ... Now let's look at a few examples of how a coffee cup calorimeter can be used as a tool to answer some typical lab questions.
Read more

Calorimetry Lab by adriana b on Prezi

Safety in this lab is very important due to the fact that this lab requires the use of fire and high temperatures. During the experiment one must wear ...
Read more

Calorimetry Lab - Charlene Parsons - Google Sites

CALORIMETRY LAB. PRE-LAB QUESTIONS. 1. Of the food items we will be testing, hypothesize which one will have the most calories and which will have the least.
Read more

Calorimetry Lab Gizmo : ExploreLearning

Investigate how calorimetry can be used to find relative specific heat values when different substances are mixed with water. Modify initial mass and ...
Read more

Lab: Calorimetry - 50Webs

Calorimetry Objective. In this lab students will measure the heat capacity of a coffee-cup calorimeter and use it to measure the molar heat of solution of ...
Read more

Calorimetry: Crash Course Chemistry #19 - YouTube

Calorimetry: Crash Course Chemistry #19 ... Lab Techniques & Safety: Crash Course Chemistry #21 - Duration: 9:03. CrashCourse 563,054 views.
Read more


CHEMISTRY 1 – CALORIMETRY LAB NAME ... Run the Logger Pro file “Calorimetry Lab” in the Chemistry 1 folder on the desktop.
Read more

SETARAM Instrumentation - Calorimetry & Thermal Analysis

SETARAM Instrumentation is an official sponsor of STOHT16 and the TECHNICAL WORKSHOPS ... leading manufacturer of calorimetry, thermal analysis and gas ...
Read more